New OEM Genuine Nissan wiper arm nut cover. Will fit 1979-83 Datsun 280ZX front and rear wipers.
One New OEM Genuine Nissan wiper arm cap nut. This wiper arm nut will fit Datsun 240Z, 260Z, and 280Z , 1970-78. The wiper arm nut holds the wiper arm onto the wiper motor...
These are the boots that fit at the base of the windshield wiper arm "studs" (just below the wiper arms). They simply slide over the "studs" on the wiper mechanism (no adhesive...
New reproduction wiper arm shaft boot seal. This rubber wiper seal will fit 1970-78 Datsun 240Z, 260Z, and 280Z. These rubber boots fit under the wiper arm.
New OEM genuine Nissan wiper arm shaft boot seal for 1970-78 Datsun 240Z, 260Z and 280Z. This boot installs under the wiper arms.
New wiper arm for Datsun 240Z, 260Z, 280Z and 280ZX, 1970-83. Choose from 17" or 18". We have found the 18" to be typical of what was used on all years but the 17" will work...
New wiper arm for Datsun 240Z, 260Z, 280Z and 280ZX, 1970-83. Choose from 17" or 18". We have found the 18" to be typical of what was used on all years but the 17" will work...
New pair of OEM Nissan original replacement metal wire wiper blade. This wiper will fit Datsun 240Z, 260Z, and 280Z, 1970-76. 18" long.
Cowl panel to innder fender drain tube for Datsun 510, 1968-73. Obsolete part that has been recreated with 3D printing to make a functional part. Flexible rubber type material...
Cowl panel screw set for Datsun 280Z 75-78. The 280Z uses a slightly larger screw diameter than the 240Z, these are 5mm thread size. Includes 4 stainless steel screws and flat...
New replacement steel cowl panel for 1970-78 Datsun 240Z, 260Z and 280Z.
Reproduction cowl area water drain tube. This tube will fit right or left sides on Datsun 240Z, 260Z and 280Z, 1970-78. This tube is located above where your feet would be in...
Reproduction cowl area water drain tube. This tube will fit right or left sides on Datsun 240Z, 260Z and 280Z, 1970-78. This tube is located above where your feet would be in...
New OEM Nissan wiper linkage cup for Datsun 280ZX, 1979-83. Plastic cup that connects the wiper arm linkage to the ball.
New wiper motor hardware kit for Datsun 240Z, 260Z and 280Z. Includes three stainless steel screws for mounting the motor and zinc nut and washer for the motor stud.
New wiper motor hardware kit for Datsun 240Z, 260Z and 280Z. Includes three stainless steel screws for mounting the motor and zinc nut and washer for the motor stud.
New wiper motor hardware kit for Datsun 240Z, 260Z and 280Z. Includes three stainless steel screws for mounting the motor and zinc nut and washer for the motor stud.
New Honda wiper motor for upgrading the stock motor. This wiper motor will require modifications to be installed in your Datsun 240Z, 260Z and 280Z, 1970-78.
New Honda wiper motor for upgrading the stock motor. This wiper motor will require modifications to be installed in your Datsun 240Z, 260Z and 280Z, 1970-78. Not even close to a...
New Honda wiper motor for upgrading the stock motor. This wiper motor will require modifications to be installed in your Datsun 240Z, 260Z and 280Z, 1970-78. Not even close to a...
New OEM clip for holding the wiper motor wiring harness to the bracket on Datsun 240Z, 260Z and 280Z.
New OEM clip for holding the wiper motor wiring harness to the bracket on Datsun 240Z, 260Z and 280Z.
New OEM Nissan rubber plug that can be modified for use as a grommet for the wiper motor wiring through the firewall. This plug fits the hole diameter and will need to have a...